Surface mount adhesive SMT red glue

FOB Reference Price:Get Latest Price
5 Piece/Pieces (Min. Order)
Report Suspicious Activity
Quick Details
Place of Origin:
Fujian, China (Mainland)
Other Adhesives
Main Raw Material:
Packing, SMT Screen printing
Brand Name:
Model Number:
Packaging & Delivery
Packaging Details
45g/tube, 75g/tube, 200g/bottle, 350g/bottle
Lead Time :
5-15 days


Surface mount adhesive SMT red glue
1) high speed dispensing
2) high dot profile
3) high wet strength
4) Excellent thixotrop


            Surface mount adhesive SMT red glue          




PRODUCT DESCRIPTION                                                        

Smt red gel provides the following product characteristics:



Chemical Type


Appearance (uncured)

Red viscous gel


One component - requires no mixing


Heat Cure


Surface Mount Adhesive

Key Substrates

Electronic components to printed circuit boards.

Other Application Areas

Small Parts Bonding

Dispense Method

Stencil print

Wet Strength


Dot Profile


SB-300 is designed for the bonding of surface mount devices to printed circuit boards prior to wave soldering. Particulary suited where very high speed dispensing, high dot profile, high wet strength and high electrical specifications are required.



Specific Gravity @ 25°C                                             1.25

Yield value @ 25°C, Pa:

Cone & Plate Rheometer, M10 with PK1, 2° Cone:

Casson Model over 0.4- 30 sec-1                                     250 to 700


TYPICAL CURING PERFORMANCE                                             

Recommended conditions for curing are exposure to heat above 100°C (typically 120~150 secs @ 150°C). Rate of cure and final strength will depend on the residence time at the cure temperature.


TYPICAL PROPERTIES OF CURED MATERIAL                                

Cured for 30 seconds @ 150°C.

Physical Properties:

Coefficient of Thermal Expansion, ASTM D 696, K-1                      145×10-6

Coefficient of Thermal Conductivity, ASTM C177, W.m-1 K-1                0.40

Specific Heat, K-1                                             0.30

Density, BS 5350, g/cm³ 1.40

Glass Transition Temperature, (Tg), ASTM E 228, °C                      110

Electrical Properties:

Dielectric Constant / Loss, ASTM D 150:

1kHz                                                            3.70 / 0.02

10 kHz                                                          3.30 / 0.02

1 MHz                                                          3.20 / 0.03

10 MHz                                                         3.10 / 0.03

Volume Resistivity, ASTM D 257, .cm                                4×1015

Surface Resistivity, ASTM D 257,                                     4×1015


Direction for use                                                                

1. After storage in a refrigerator the adhesive must be allowed to equilibrate to room temperature before use, typically 12 hours.

2. Avoid cross contamination with other epoxy or acrylic adhesives by ensuring dispense nozzels, adapters etc. are thoroughly cleaned.

3. The quantity of adhesive dispensed will depend on the dispense pressure, time, nozzle size and temperature.

4. These parameters will vary depending on the type of dispensing system use and should be optimised accordingly.

5. Bath temperature should ideally be controlled at a value between 25°C-30°C, 50%RH for optimum results. Under these conditions product will remain dispensable in the tray for at least 2 to 3 days.

6. Uncured adhesive can be cleaned from the board with isopropanol, MEK or glycol ether blends such as Prozon.



Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Products shall be maintained, optimally, at temperatures between 2°C to 8°C unless otherwise labeled, or, specified. Storage, at temperatures below 2°C, or, greater than 8°C, is not recommended. Temperatures below 2°C and above 8°C can adversely affect product properties.